Home  /  Thermal spray  /  Flame spraying

Flame spraying

Flame (combustion) spraying melts the feedstock — powder or wire — with an oxygen-and-fuel flame and applies it to the surface. It is a cost-effective solution for metallic and ceramic coatings resistant to wear and corrosion. The flame temperature is about 3,100 °C.

Flame spraying, Poland. Arranged at a vetted plant in Poland, to order, with a non-binding enquiry.

We do not carry out flame spraying ourselves. reliq is your first point of contact — send us an enquiry and we will connect you with a proven plant in Poland, help you choose the technology and handle communication. You then sign the order, contract and warranty directly with the plant.

Heat source
Flame (oxygen + fuel)
Feedstock
Powder or wire
Benefit
Cost-effective
Step 1
Flame
An oxygen-and-fuel torch creates a flame.
Step 2
Melting the material
The feedstock (powder or wire) melts and is atomised in the flame.
Step 3
Coating
Molten particles hit the surface; some coatings are then fused for extra hardness.

What is flame spraying

Flame (combustion) spraying melts the feedstock — powder or wire — with an oxygen-and-fuel flame and applies it to the surface. It is a cost-effective method for metallic and ceramic coatings; the coatings usually contain more oxides and have higher porosity, sometimes a rougher finish, with moderate adhesion.

What it is for

Flame spraying is an economical solution for wear and corrosion resistance, thermal barriers and clearance control, and for restoring worn parts. Some coatings are fused, making them very hard and corrosion resistant.

When to choose flame spraying

It suits less demanding applications and where cost matters. For the highest quality and density, choose HVOF; for ceramics and thermal barriers, Air Plasma Spray (APS).

Typical parts

Thermal spray coatings are used on both new and refurbished parts, for example:

Coating materials

Depending on the operating conditions, a wide range of materials is used — carbides (high hardness and abrasion resistance), alloys and superalloys, ceramics and cermets.

Coating thickness and renovation

Depending on the technology and purpose, the coating thickness ranges from tenths of a millimetre to several millimetres. The coating can replace missing material and restore a worn part to its original dimension; on precise surfaces an allowance is left for subsequent grinding.

Industries

Engineering, power generation, mining and metallurgy, petrochemical and chemical industry, paper and printing, glass, pumps and hydraulics, electrical engineering, automotive and aerospace.

FAQ

How does flame spraying differ from HVOF?

Flame spraying is cheaper, but the coatings tend to be more porous and less adherent. HVOF gives a denser, more adherent coating thanks to high particle velocity.

Can a flame-sprayed coating be strengthened?

Yes, some coatings are fused, making them very hard and corrosion resistant.

Does reliq carry out flame spraying itself?

No. reliq is an agent: we connect you with a proven plant in Poland and help you choose the technology and handle communication.

What is the typical coating thickness?

Depending on the technology, material and purpose, usually from tenths of a millimetre to several millimetres. On precise surfaces an allowance is left for subsequent grinding.

Can a worn part be repaired by thermal spraying?

Yes. The coating replaces missing material and restores the dimensions of worn surfaces — e.g. shafts, pins, bearing seats or piston rods. The surface is then machined or ground to the required dimension.

Does the coating increase the dimension, and can it be machined?

Yes, the coating adds material to the surface. For functional and precise dimensions it is ground, turned or honed after spraying; hard coatings are ground with diamond or CBN tools.

Is the coating firmly bonded to the base material?

With proper surface preparation the coating has very good adhesion. The bond is mainly mechanical, in some systems supported by a bond coat.

What should I send for a quotation?

Ideally a drawing of the part, the material, photos, a description of the operating load, the required thickness or final dimension, the roughness and the number of pieces; and whether it is a new part or a renovation.

Need a flame-sprayed coating?

Send us a non-binding enquiry. We will connect you with a proven plant in Poland and help you choose the technology and material.

Send an enquiry →

← Back to thermal spraying