Nitriding is a low-temperature thermochemical treatment in which the steel surface is enriched with nitrogen (typically around 500–520 °C). It increases wear resistance, hardness and fatigue life, and because the part is not quenched, it has the lowest distortion of all these processes. It suits precise, finished parts.
Nitriding, Poland. Arranged at a vetted plant in Poland, to order, with a non-binding enquiry.
We do not carry out nitriding ourselves. reliq is your first point of contact — send us an enquiry and we will connect you with a proven plant in Poland, help you choose the technology and handle communication. You then sign the order, contract and warranty directly with the plant.
Nitriding is a low-temperature thermochemical process that increases wear resistance, surface hardness and fatigue life by diffusing nitrogen into the surface and forming hard nitrides. It runs typically around 500–520 °C and — crucially — without any subsequent quench, so distortion is very low.
The case usually consists of two zones. On the surface is the compound (white) layer, which provides the main benefit — high resistance to wear, scuffing and seizure. Beneath it lies the diffusion zone with dissolved nitrogen, which raises fatigue strength, mainly thanks to compressive stresses at the surface. Parts are usually quenched and tempered before nitriding.
The nitrided depth is shallow (of the order of tenths of a millimetre), but surface hardness is very high (over 900–1100 HV on suitable steels). There is no single standard for nitriding depth.
Nitriding is the choice where a hard, wear- and fatigue-resistant surface with minimal distortion is needed — on precise, finished parts that no longer need straightening or machining.
Nitriding is most effective on steels with nitride-forming elements (chromium, molybdenum, vanadium, aluminium), e.g. 31CrMoV9 or 34CrAlMo5. Adding a carbon-bearing gas gives nitrocarburising.
| Aspect | Nitriding | Nitrocarburising (FNC) |
|---|---|---|
| Element | nitrogen | nitrogen + a little carbon |
| Temperature | ~500–520 °C | ~570 °C |
| Quench | not needed | not needed |
| Materials | nitriding and tool steels | also unalloyed steels, cast iron |
The best results are achieved with steels alloyed with aluminium, chromium, molybdenum and vanadium, which form hard nitrides with nitrogen — typically 31CrMoV9 (1.8519), 34CrAlNi7-10 (1.8550), 42CrMo4 (1.7225), as well as tool and stainless steels. Before nitriding the steel is usually quenched and tempered so the core keeps its strength.
Depending on the steel, surface hardness ranges roughly from 600 to 1200 HV. The nitriding depth (Nht) is usually from tenths of a millimetre up to about 0.6 mm; a thin compound (white) layer a few micrometres thick forms on the surface, with a diffusion layer beneath. Depth and hardness are controlled to suit the load.
Gears and pinions, shafts and camshafts, crankshafts, extruder screws, moulds and dies, valve components, guiding and sliding surfaces — wherever a wear- and fatigue-resistant surface with minimal distortion is required.
No. Nitriding runs at low temperature (typically around 500–520 °C) and forms the hard case without any subsequent quench, which means minimal distortion.
Two zones: the compound (white) layer on the surface (wear and scuffing resistance) and the diffusion zone beneath it (fatigue strength).
Most effectively steels with nitride-forming elements (chromium, molybdenum, vanadium, aluminium), e.g. 31CrMoV9 or 34CrAlMo5, and tool steels.
No. reliq is an agent: we connect you with a proven plant in Poland and help you choose the technology and handle communication. You sign the order and warranty directly with the plant.
reliq is an agent — we do not carry out nitriding ourselves. Send us a non-binding enquiry and we will arrange it at a vetted plant in Poland; we help with the technology and communication, and you contract directly with the plant.
The price depends on the material, size, number of pieces and the required depth and hardness. Send a drawing or description of the part, the material, the quantity and the requirements — we will prepare a quotation at a vetted plant.
Best are steels alloyed with Al, Cr, Mo, V (e.g. 31CrMoV9, 34CrAlNi7-10, 42CrMo4), plus tool and stainless steels. Plain carbon steels give lower hardness.
Depending on the steel, roughly 600–1200 HV at the surface and a nitriding depth from tenths of a millimetre up to about 0.6 mm. Parameters are chosen to suit the load.
Distortion is minimal — nitriding runs at a low temperature (~500–520 °C) and without quenching, so it suits precise, finish-machined parts.
Send us a non-binding enquiry. We will connect you with a proven plant in Poland and help you choose the technology and parameters.
Send an enquiry →